Accurate and Reliable Test Results
888-433-5736

facilities Info Available Tests Contact

(Get this document in PDF format)

A2LA

SCOPE OF ACCREDITATION TO ISO/IEC 17025-2005

DELSEN TESTING LABORATORIES, INC.

1024 Grand Central Avenue

Glendale, CA 91201

John Moylan Phone: 818 247 4106

 

MECHANICAL

Valid To: July 31, 2010            Certificate Number: 0096.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests:

Test Method:   Test Title:   
ASTM B117 Practice for Operating Salt Spray (Fog) Testing Apparatus
ASTM B368 Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
ASTM B487 Test Method for Metal and Oxide Coating Thickness by  Microscopical Examination of a Cross Section
ASTM C271 Test Method for Density of Sandwich Core Materials
ASTM C273 Test Method for Shear Properties in Flatwise Plane of Flat Sandwich Constructions or Sandwich Cores
ASTM C297 Test Method for Tensile Strength of Flat Sandwich Constructions in Flatwise Plane
ASTM C364   Test Method for Edgewise Compressive Strength of Flat Sandwich Constructions
ASTM C365 Test Methods for Flatwise Compressive Strength of Sandwich Cores
ASTM C393 Test Method for Flexural Properties of Flat Sandwich Constructions
ASTM C1166 Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories
ASTM D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ASTM D150 Test Methods for A-C Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulating Materials
ASTM D256  Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D257 Test Methods for D-C Resistance or Conductance of Insulating Materials 
ASTM D395 Test Methods for Rubber Property- Compression Set (Method B)   (except para. 8.4.1)
ASTM D412 Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermoplastic Elastomers- Tension
ASTM D471 Test Method for Rubber Property- Effect of Liquids (Section 15 only)  
ASTM D495 Test Method for High-Voltage, Low-Current, Dry Arc-Resistance of Solid Electrical Insulation
ASTM D570 Test Method for Water Absorption of Plastics
ASTM D575 Test Methods for Rubber Properties in Compression

Test Method: Test Title:  
ASTM D624  Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers (Die B & C)
ASTM D621-64(88 ) Test Methods for Deformation of Plastics Under Load (Withdrawn)
ASTM D635 Test Method for Rate of Burning and/or Extent and Time
(except para. 6.3) Burning of Self-Supporting Plastics in a Horizontal Position
ASTM D638 Test Method for Tensile Properties of Plastics
ASTM D695   Test Method for Compressive Properties of Rigid Plastics 
ASTM D732  Test Method for Shear Strength of Plastics by Punch Tool  
ASTM D746   Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
ASTM D785 Test Method for Rockwell Hardness of Plastics and  Electrical Insulating Materials
ASTM D790  Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement (Method A)
ASTM D877 Test Method for Dielectric Breakdown Voltage of Insulating Liquids Using Disk Electrodes
ASTM D882  Test Methods for Tensile Properties of Thin Plastic Sheeting
ASTM D903  Test Method for Peel or Stripping Strength of Adhesive Bonds 
ASTM D924 Test Method for Dissipation Factor (or Power Factor) and Relative Permittivity (Dielectric Constant) or Electrical Insulating Liquids
ASTM D952 Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials
ASTM D953   Test Method for Bearing Strength of Plastics
ASTM D991 Test Method for Rubber Property- Volume Resistivity of Electrically Conductive and Antistatic Products
ASTM D1002 Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D1004 Test Method for Initial Tear Resistance of Plastic Film and Sheeting
ASTM D1043 Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test
ASTM D1169  Test Method for Specific Resistance (Resistivity) of Electrical Insulating Liquids
ASTM D1238  Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer 
ASTM D1621 Test Method for Compressive Properties of Rigid Cellular Plastics
ASTM D1622 Test Method for Apparent Density of Rigid Cellular Plastics  
ASTM D1708 Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D1781 Test Method for Climbing Drum Peel for Adhesives
ASTM D1876 Test Method for Peel Resistance of Adhesives (T-Peel Test) 
ASTM D2095 Test Method for Tensile Strength of Adhesives by Means of Bar and Rod Specimens
ASTM D2137 Test Methods for Rubber Property- Brittleness Point of Flexible Polymers and Coated Fabrics
ASTM D2240 Test Method for Rubber Property- Durometer Hardness  
ASTM D2295 Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal)
ASTM D2344 Test Method for Apparent Interlaminar Shear Strength of Parallel Fiber Composites by Short-Beam Method
ASTM D2520 Test Method for Complex Permittivity (Dielectric Constant) of Solid Electrical Insulating Materials at Microwave Frequencies and Temperatures to 1650°C

                                                                                                    <return to top of page>

 

Test Method: Test Title:
ASTM D2557 Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from -267.8 to -55°C (-450 to -67°F)
ASTM D2583 Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D2584 Test Method for Ignition Loss of Cured Reinforced Resins 
ASTM D2843 Test Method for Density of Smoke from the Burning or Decomposition of Plastics
ASTM D2919 Test Method for Determining Durability of Adhesive Joints Stressed in Shear by Tension Loading
ASTM D3039 Test Method for Tensile Properties of Polymer Matrix Composite Materials
ASTM D3163 Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading
ASTM D3164 Test Method for Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading
ASTM D3165 Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies
ASTM D3167 Test Method for Floating Roller Peel Resistance of Adhesives 
ASTM D3171 Test Method for Fiber Content of Resin-Matrix Composites by Matrix Digestion (Method A, B, F & G)
ASTM D3330 Test Method for Peel Adhesion of Pressure-Sensitive Tape   
ASTM D3359 Test Methods for Measuring Adhesion by Tape Test
ASTM D3386-00 Test Method of Coefficient of Linear Thermal Expansion of Electrical Insulating Materials (withdrawn)
ASTM D3410 Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
ASTM D3417-99 Test Method for Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry (DSC) (withdrawn )
ASTM D3418 Test Method for Transition Temperatures of Polymers by Thermal Analysis
ASTM D3479  Test Methods for Tension-Tension Fatigue of Oriented Fiber,Resin Matrix Composites
ASTM D3518 Practice for In-Plane Shear Stress-Strain Response of Unidirectional Polymer Matrix Composite Materials by Tensile Test of [+/-45] Laminate
ASTM D3528  Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
ASTM D3529  Test Method for Resin Solids Content of Epoxy-Matrix Prepreg by Matrix Dissolution
ASTM D3530 Test Method for Volatiles Content of Epoxy-Matrix Prepreg
ASTM D3531 Test Method for Resin Flow of Carbon Fiber-Epoxy Prepreg 
ASTM D3532   Test Method for Gel Time of Carbon Fiber-Epoxy Prepreg 
ASTM D3846 Test Method for In-Plane Shear Strength of Reinforced Plastics 
ASTM D3850 Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials by Thermogravimetric Method
ASTM D4255 Guide for Testing In-Plane Shear Properties of Composite Laminates
ASTM D4475 Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods by the Short-Beam Method 
ASTM D4496 Test Method for D-C Resistance or Conductance of Moderately Conductive Materials
ASTM D4591  Test Method for Determining Temperatures & Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D5379 Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method

                                                                                                      <return to top of page>.

Test Method:   Test Title
ASTM D5420 Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D5467 Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam
ASTM D5528 Mode I Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composite
ASTM D5656 Test Method for Thick Adherend Metal Lap-Shear Joints for Determination of the Stress-Strain Behavior of Adhesives in Shear by Tension Loading
ASTM D5766 Open Hole Tensile Strength of Polymer Matrix Composite Laminates  
ASTM D5961  Test Method for Bearing Response of Polymer Matrix Composite Laminates
ASTM D6110 Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D6272 Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D6415 Test Method for Measuring the Curved Beam Strength of a Fiber Reinforced Polymer Composite
ASTM D6484 Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
ASTM D6742 Filled Hole Tension and Compression Testing of Polymer Matrix Composites
ASTM D6641  Test Method for Determining the Compressive Properties of Polymer Matrix Composite Laminate Using a Combined Loading Compression (CLC) Test Fixture
ASTM D7028 Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM D7078 Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method
ASTM D7136 Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event
ASTM D7137 Test Method for Compressive Residual Strength Properties of Damaged Polymer Matrix Composite Plates
ASTM D7249 Test Method for Facing Properties of Sandwich Constructions by Long Beam Flexure
ASTM D7291 Test Method for Through-Thickness "Flatwise" Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material
ASTM D7332 Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite
ASTM E3  Practice for Preparation of Metallographic Specimens  
ASTM E662 Test Method for Specific Optical Density of Smoke Generated by Solid Materials
ASTM E831 Test method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis
ASTM E1131 Test Method for Compositional Analysis by Thermogravimetry 
ASTM E1269 Determining Specific Heat Capacity by DSC
ASTM E1356 Test Method for Glass Transition Temperatures by Differential Scanning Calorimetry or Differential Thermal Analysis (DSC Only)
ASTM E1545 Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis
ASTM E1640  Test Method for Assignment of the Glass Transition Temperature by Dynamic Mechanical Analysis

        :                                                                                             <return to top of page>.

Test Method Test Title:
ASTM F814-84b  Discontinued 1995; Test Method for Specific Optical Density of Smoke Generated by Solid Materials for Aerospace Applications
ASTM G85 (A1) Practice of Modified Salt Spray (Fog) Testing 
ASTM G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
   
DIN EN 2564 Aerospace Series-Carbon Fibre Laminates – Determination of Fibre,   Resin, and Void Contents
DIN EN 2850  Aerospace Series Carbon-Fibre Thermosetting Resin Unidirectional Laminates – Compression Test Parallel to the Fibre Direction
   
EN ISO 527 Plastics – Determination of Tensile Properties
EN ISO 14125 Fibre-reinforced Plastic Composites – Determination of the Flexural Properties
ISO 14126 Fibre-Reinforced Plastic Composites – Determination of Compressive Properties in the In-Plane Direction
ISO 14129  Fibre-Reinforced Plastic Composites – Determination of the In-Plane Shear Strain Response, including the In-Plane Shear Modulus and Strength by the +/-45 Tension Test Method
   
DOT  
DOT MVSS 302 Department of Transportation Motor Vehicle Safety Standard Flammability of Interior Materials
   
FAA:  
FAR 25.853  Airworthiness Standards: Transport Category Airplanes, Fire Protection, Compartment Interiors, Appendix F, Part I, IV, and V.
   
NASA:  
1092  Standard Tests for Toughened Resin Composites 
1142 NASA/Aircraft Industry Standard Specification for Graphite Fiber-Toughened Thermoset Composite Materials
   
Boeing:  
BSS 7230 Determination of Flammability Properties of Aircraft Materials  
BSS 7238 Test Method for Smoke Generation by Materials on Combustion
BSS 7239 Test Method for Toxic Gas Generation by Materials on Combustion  
BSS 7322 Boeing Specification Support Standard, Ohio State University Calorimeter Heat Release, Determination of Airbus:
   
ABD 0031 Fireworthiness Requirements Pressurized Section of Fuselage
   
AITM 2.0002 Flammability of Non-metallic Materials,- Small Burner Test, vertical
AITM 2.0003 Flammability of Non-metallic Materials,- Small Burner Test, horizontal  
AITM 2.0004 Flammability of Non-metallic Materials,- Small Burner Test, 45 degree 
AITM 2.0005 Flammability of Non-metallic Materials,- Small Burner Test, 60 degree
AITM 2.0006 Determination of Heat Release Rate of Aircraft Materials  
AITM 2.0007 Determination of Specific Optical Smoke Density of Aircraft Interior Materials
AITM 2.0008 Determination of Specific Optical Smoke Density of Wire/Cable Insulation
AITM 2.0038 Flammability of Heat Shrinkable Tubing’s,- Small Burner Test, 60 degree
AITM 3.0005 Determination of Specific Gas Components of Smoke Generated by Non-metallic Aircraft Materials inside the Pressurized ection of Fuselage

 

:                                                                                                                  <return to top of page>

Test Method: Test Title:
Military Standards:  
MIL-I-46058 General Specification for Insulating Compound, Electrical (For Coating Printed Circuit Assemblies) (Except Fungus) 
MIL-P-55110 General Specification for Printed Wiring Board, Rigid
MIL-S-13949 General Specification for Sheet, Printed Wiring Board (Except Fungus)
MIL-PRF-31032 General Specification for Printed Circuit Board/Printed Wiring Board
MIL-PRF-50884 General Specification for Printed-Wiring, Flexible and Rigid-Flex
MMM-A-132 Federal Specification, Adhesives, Heat Resistant, Airframe Structural, Metal-to-Metal (Except Creep)
MIL-STD-810 Environmental Engineering Considerations and Laboratory Tests
     Method 501 High Temperature  
     Method 502 Low Temperature 
     Method 503 Thermal Shock
     Method 507 Humidity
     Method 509 Salt Fog
     Method 514 Vibration (Selected Methods)  
     Method 516 Shock
MIL-STD-202 Test Methods for Electronic and Electrical Component Parts
     Method 101 Salt Atmosphere (Corrosion) 
     Method 103 Humidity (Steady State) 
     Method 104 Immersion (Method A)
     Method 106 Moisture resistance
     Method 107 Thermal shock
     Method 108 Life (At Elevated Ambient Temperature)
     Method 201 Vibration
     Method 204 Vibration, high frequency
     Method 301 Dielectric withstanding voltage
     Method 302  Insulation resistance
     Method 303  DC resistance
     Method 306 Quality factor (Q)  
     Method 307 Contact resistance
   
SACMA (Suppliers of Advanced Composite Materials Association):
   SRM 1-94 Compressive Properties of Oriented Fiber-Resin Composites 
   SRM 2-94  Compression After Impact Properties of Oriented Fiber-Resin Composites
   SRM 3-94  Open-Hole Compression Properties of Oriented Fiber-Resin Composites 
   SRM 4-94 Tensile Properties of Oriented Fiber-Resin Composites  
   SRM 5-94   Open-Hole Tensile Properties of Fiber-Resin Composites 
   SRM 6-94 Compressive Properties of Oriented Cross-Plied Fiber-Resin Composites
   SRM 7-94  In-Plane Shear Stress-Strain Properties of Oriented Fiber-Resin Composites
   SRM 8-94  Short Beam Shear Strength of Oriented Fiber-Resin Composites  
   SRM 9-94     Tensile Properties of Oriented Cross-Plied Fiber-Resin Composites  
   SRM 10-94 Fiber Volume, Percent Resin Volume and Calculated Average Cured Ply Thickness of Plied Laminates
   SRM 11R-94 Environmental Conditioning of Composite Test Laminates 
   SRM 18R-94 Glass Transition Temperature (Tg) Determination By DMA 
   SRM 21R-94 Fluid Resistance Evaluating of Composite Materials
   SRM 22R-94 Determining the Resin Flow of Preimpregnated “B” Staged Material  

                                                                                                                   <return to top of page>.

Test Method:  Test Title:     
SACMA (Suppliers of Advanced Composite Materials Association) cont.:
SRM 23R-94 Determination of Resin Content and Fiber Areal Weight of Thermoset Prepreg with Destructive Techniques
SRM 25R-94 Onset Temperature and Peak Temperature for Composite Resin Systems Using Differential Scanning Calorimetry (DSC)
IPC:
  
   IPC-4101   Specification for Base Materials for Rigid and Multilayer Printed Boards 
   IPC-6012 Qualification and Performance Specification for Rigid Printed Boards  
   IPC-6013 Qualification and Performance Specification for Flexible Printed Boards 
   IPC-CC-830 Qualification and Performance of Electrical Insulating Compound                        
                                                for Printed Board Assemblies (Except FT-IR)
   IPC J-STD-003 Solderability Tests for Printed Boards
   IPC-SM-840 Qualification and Performance of Permanent Solder Mask  
IPC-TM 650  Test Methods Manual    
IPC-TM-650 Test Methods:
   2.1.1  Microsectioning  
   2.1.1.1  Microsectioning, Ceramic Substrate 
   2.1.6 Thickness of Glass Fabric             2
   2.1.6.1  Weight of Fabric Reinforcements  
   2.1.7 Thread Count of Glass Fabric (Method A)  
   2.1.7.1   Thread Count, Organic Fibers  
   2.1.8  Workmanship
   2.2.1 Mechanical Dimensional Verification
   2.2.2   Optical Dimensional Verification
   2.2.4  Dimensional Stability, Flexible Dielectric Materials
   2.2.5   Dimensional Inspections Using Microsections  
   2.2.12.2 Weight and Thickness of Copper Foils with Releasable Carriers
   2.2.12.3    Weight and Thickness Determination of Copper Foils With Etchable Carriers
   2.2.18 Determination of Thickness of Laminates by Mechanical Measurement  
   2.2.18.1 Determination of Thickness of Metallic Clad Laminates, Cross-sectional 
   2.2.19.1  Length, Width and Perpendicularity of Laminate and Prepreg Panels
   2.3.2       Chemical Resistance Of Flexible Printed Wiring Material
   2.3.4  Chemical Resistance, Marking Paints and Inks
   2.3.4.2   Chemical Resistance of Laminates, Prepreg and Coated Foil Products,by Solvent Exposure
   2.3.5 Density, Insulating Material  
   2.3.6 Etching, Ammonium Persulfate Method 
   2.3.7 Etching, Ferric Chloride Method
   2.3.7.1  Cupric Chloride Etching Method
   2.3.7.2 Alkaline Etching Method 
   2.3.8  Flammability, Flexible Insulating Materials
   2.3.8.1 Flammability of Flexible Printed Wiring 
   2.3.9 Flammability of Prepreg and Thin Laminate 
   2.3.10  Flammability of Laminate  
   2.3.10.1 Flammability of Soldermask on Printed Wiring Laminate
   2.3.16   Resin Content of Prepreg, by Burn-off   
   2.3.16.1 Resin Content of Prepeg, by Treated Weight  

                                                                                                             <return to top of page>.

Test Method: Test Title:   
IPC-TM-650 Test Methods (cont.):
   2.3.16.2  Treated Weight of Prepreg 
   2.3.17    Resin Flow Percent of Prepreg
   2.3.17.1 Resin Flow of Adhesive Coated Films and Unsupported Adhesive Films  
   2.3.17.2 Resin Flow of "No Flow" Prepreg   
   2.3.18 Gel Time, Prepreg Materials   
   2.3.19    Volatile Content of Prepreg 
   2.3.23     Cure (Permanency) Thermally Cured Solder Mask   
   2.3.24.2   Porosity of Metallic Coatings on Copper-Based Alloys and  Nickel (Nitric Acid Vapor Test)
   2.3.25   Detection and Measurement of Ionizable Surface Contaminants by Resistivity of Solvent Extract
   2.3.29   Flammability, Flexible Flat Cable
   2.3.37 Volatile Content of Adhesive Coated Dielectric Films   
   2.3.38        Surface Organic Contaminant Detection Test
   2.3.40  Thermal Stability
   2.4.1  Adhesion, Tape Testing
   2.4.1.6      Adhesion, Polymer Coating  
   2.4.2.1      Flexural Fatigue and Ductility, Foil  
   2.4.3.1    Flexural Fatigue and Ductility, Flexible Printed Wiring   
   2.4.3.2   Flexural Fatigue and Ductility, Flexible Metal-Clad Dielectrics  
   2.4.4     Flexural Strength of Laminates (at Ambient  Temperature)   
   2.4.4.1 Flexural Strength of Laminates (at Elevated Temperature) 
   2.4.5.1         Flexibility - Conformal Coating  
   2.4.7        Machinability, Printed Wiring Materials 
   2.4.8   Peel Strength of Metallic Clad Laminates
   2.4.8.1   Peel Strength, Metal Foil (Keyhole Method for Thin Laminates)  
   2.4.8.2 Peel Strength of Metallic Clad Laminates at Elevated Temperature (Hot Fluid Method)
   2.4.8.3  Peel Strength of Metallic Clad Laminates at Elevated Temperature    (Hot Air Method)
   2.4.9  Peel Strength, Flexible Dielectric Materials   
   2.4.13    Solder Float Resistance Flexible Printed Wiring Materials    
   2.4.13.1  Thermal Stress of Laminates         2
   2.4.18.1  Tensile Strength and Elongation, In-House Plating    
   2.4.19  Tensile Strength and Elongation, Flexible Printed Wiring Materials      
   2.4.21   Land Bond Strength, Unsupported Component Hole   
   2.4.22      Bow and Twist (Percentage)  
   2.4.24     Glass Transition Temperature and Z-Axis Thermal Expansion by TMA 
   2.4.24.1      Time to Delamination (TMA Method)  
   2.4.24.4    Glass Transition and Modulus of Materials Used in High Density Interconnection (HDI) and Microvias -DMA Method
   2.4.24.5  Glass Transition Temperature and Thermal Expansion of Materials Used In High Density Interconnection (HDI) and Microvias -TMA Method
   2.4.25 Glass Transition Temperature and Cure Factor by DSC                      
   2.4.27.2    Solder Mask Abrasion (Pencil Method) 
   2.4.28  Adhesion, Solder Mask (Non-Melting Metals)  
   2.4.28.1  Adhesion, Solder Resist (Mask), Tape Test Method 

 

                                                                                                                <return to top of page>.

Test Method:    Test Title: 
IPC-TM-650 Test Methods (cont.):
   2.4.36     Rework Simulation, Plated-Through Holes for Leaded Components    
   2.4.38  Prepeg Scaled Flow Testing   
   2.4.39   Dimensional Stability, Glass Reinforced Thin Laminates
   2.4.41.2 Coefficient of Thermal Expansion - Strain Gage Method
   2.4.41.3  In-Plane Coefficient of Thermal Expansion, Organic Films 
   2.5.1   Arc Resistance of Printed Wiring Materials 
   2.5.5.1      Permittivity (Dielectric Constant) and Loss Tangent (Dissipation Factor) of Insulating Material at 1MHz (Contacting Electrode Systems)
   2.5.5.2  Dielectric Constant and Dissipation Factor of Printed Wiring Board Material--Clip Method
   2.5.5.4  Dielectric Constant and Dissipation Factor of Printed Wiring Board Material--Micrometer Method
  2.5.5.5  Stripline Test for Permittivity and Loss Tangent (Dielectric Constant and Dissipation Factor) at X-Band
   2.5.6 Dielectric Breakdown of Rigid Printed Wiring Material   
   2.5.6.2  Electric Strength of Printed Wiring Material 
   2.5.6.3 Dielectric Breakdown Voltage and Dielectric Strength  
   2.5.7 Dielectric Withstanding Voltage, PWB
   2.5.7.1     Dielectric Withstanding Voltage - Polymeric Conformal Coating  
    2.5.8   Dissipation Factor of Flexible Printed Wiring Material  
    2.5.11 Insulation Resistance, Multilayer Printed Wiring (Within a Layer)  
    2.5.12        Interconnection Resistance, Multilayer Printed Wiring   
    2.5.17 Volume Resistivity and Surface Resistance of Printed Wiring Materials 
    2.5.17.1   Volume and Surface Resistivity of Dielectric Materials 
    2.5.17.2    Volume Resistivity of Conductive Resistance Used in High Dentisty Interconnection (HDI) and Microvias, Two-Wire Method
    2.5.27 Surface Insulation Resistance of Raw Printed Wiring Board Material 
    2.5.28    Q Resonance, Flexible Printed Wiring Materials 
    2.5.32   Resistance Test, Plated Through-Holes 
    2.6.2       Moisture Absorption, Flexible Printed Wiring 
    2.6.2.1   Water Absorption, Metal Clad Plastic Laminates
    2.6.3  Moisture and Insulation Resistance, Printed Boards 
    2.6.3.1   Moisture and Insulation Resistance - Solder Mask
    2.6.3.2  Moisture and Insulation Resistance, Flexible Base Dielectric     
   2.6.3.4  Moisture and Insulation Resistance – Conformal Coating
    2.6.3.5   Bare Board Cleanliness by Surface Insulation Resistance
    2.6.3.6   Surface Insulation Resistance - Fluxes –Telecommunications
    2.6.5    Physical Shock, Multilayer Printed Wiring  
    2.6.6    Temperature Cycling, Printed Wiring Board   
    2.6.7          Thermal Shock and Continuity, Printed Board   
    2.6.7.1  Thermal Shock - Conformal Coating 
    2.6.7.2  Thermal Shock, Continuity and Microsection, Printed Board   
   2.6.7.3   Thermal Shock - Solder Mask
   2.6.8  _ Thermal Stress, Plated Through-Holes  
   2.6.8.1   Thermal Stress, Laminate      
   2.6.9       Vibration, Rigid Printed Wiring  
   2.6.11         Hydrolytic Stability Solder Mask
   2.6.11.1   Hydrolytic Stability - Conformal Coating  

                                                                                                           <return to top of page>.

Test Method:  Test Title: 
IPC-TM-650 Test Methods (cont.):
   2.6.14  Resistance to Electrochemical Migration, Solder Mask   
   2.6.14.1  Electrochemical Migration Resistance Test 
   2.6.25 Conductive Anodic Filament (CAF) Resistance Test: X-Y Axis
   
SAE (Society of Automotive Engineers)
  SAE J2253  Test Procedures for Automotive Structural Composite Materials(Formerly ACCM-T-02)
   

                                                                                                               <return to top of page>.

                  

on the following materials and products:

Adhesives, composites and laminates, printed boards and electrical insulating materials, elastomers, plastics and engineering thermoplastics, graphite or boron reinforced thermoplastics, metal matrix composites, graphite/epoxy, graphite/bismaleimide, polyimide/glass, epoxy/glass, toughened epoxy systems and graphite aramid or boron reinforced epoxies, and similar materials.

<return to top of page>.

| Home | Facilities & Services | Information | Contact | Literature Library | Metallographic Image Gallery | News |


1024 Grand Central Avenue
Glendale, CA 91201
888-433-5736
Fax: 818-247-4537
info@delsen.com

© 2009 Delsen Testing Laboratories, Inc. all rights reserved

Created by LTG&A, Incorporated